English
Chinese
2022 High quality Sfp-10g-Er40 - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel Featured Image
  • 2022 High quality Sfp-10g-Er40 - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel

2022 High quality Sfp-10g-Er40 - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel

Short Description:


Download as PDF

Product Detail

Product Tags

Related Video

Feedback (2)

"Sincerity, Innovation, Rigorousness, and Efficiency" will be the persistent conception of our company to the long-term to establish together with customers for mutual reciprocity and mutual gain for Poe Over Sfp , Wtd Sfp Module , Ftth Sfp Module , We welcome new and previous buyers from all walks of life to make contact with us for upcoming organization associations and mutual good results!
2022 High quality Sfp-10g-Er40 - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel Detail:

Descriptions

Fiber type Minimum modal bandwidth @ 850 nm (MHz●km) Operatingra nge (meters)
62.5um MMF 160 2 to 26
200 2 to 33
50um MMF 400 2 to 66
500 2 to 82
2000 2 to 300

SFP+SR Operating Range for each Optical Fiber Type

The transceiver consists of two sections: The high performance 850nm VCSEL transmitter and high sensitivity PIN integrated with a TIA. Receiver.

A block diagram of the HSFP10-3831 SFP+ optical transceiver is shown below

sr

● Absolute Maximum Ratings

Parameter Symbol Min Max Unit
Storage Temperature TST -40 +85  ℃
Supply Voltage VCC3 0 +3.6 V
Relative Humidity RH 5 85 %

● Recommend Operation Environment

Parameter Symbol Min Typ Max Unit
Date Rate 10.3125 Gb/s
Supply Voltage VCC +3.14 3.3 +3.47 V
Supply Current ICC 180 200 mA
Power Dissipation PD 0.8 W
Operating Temperature TOP -5 25 +75 ℃

● Transmitter Operating Characteristic-Optical, Electrical

Parameter Symbol Min Typ Max Unit Ref.
Side Mode Suppression Ratio SMSR 30 - dBm
Average launch power of OFF transmitter Poff - -30 dBm
Extinction Ratio ER 3.5 - dB 1
Transmitter Dispersion Penalty TDP - - 3.9 dB
Operating Data Rate S 10.3125 Gbps
Centre Wavelength λC 840 850 860 nm
Spectrum Band Width (RMS) σ 0.45 nm
Average Optical Power Pavg -7.3 - -1 dBm
Optical Eye Mask Compliant with IEEE 802.3ae
Input Differential Impedance ZIN 90 100 110 Ω
TX Disable Disable 2.0 Vcc+0.3 V
Enable 0 0.8 V
TX Fault Fault 2.0 Vcc+0.3 V
Normal 0 0.8 V
Data Dependent Input Jitter DDJ 0.08 UI
Data Input Total Jitter TJ 0.25 UI

● Receiver Operating Characteristic-Optical, Electrical

Parameter Symbol Min Typ Max Unit Ref.
Center Wavelength λr 850 nm
Average receiver power PIN -11.1 dBm 2
Receiver Overload PMAX -1.0 dBm 2
Los Assert LosA -30 - dBm
Los Dessert LosD -12 dBm
Los Hysteresis LosH 0.5 2.5 5 dB
Receiver Reflectance -12 dB 1
Output Differential Impedance PIN 90 100 110 Ω
LOS High 2.0 Vcc+0.3 V
Low 0 0.8
Rx Output Rise and Fall Time Tr/Tf 30 ps 20% to 80%
Total Output Jitter TJ 0.7 UI
Data Dependent Output Jitter DJ 0.42 UI

Notes:
Note 1. Measured at 10.3125b/s with PRBS 231 – 1 NRZ test pattern.
Note 2. Under the ER worst case, measured at 10.3125 Gb/s with PRBS 231 – 1 NRZ test pattern for BER

● Control and Status I/O Timing Characteristics

Parameter Symbol Min Max Unit Ref.
TX Disable Assert Time t_off 10 µs 1
TX Disable Negate Time t_on 1 ms 2
Time to initialize including reset of TX_Fault t_init 300 ms 3
TX Fault Assert Time t_fault 100 µs 4
TX Disable to reset t_reset 10 µs 5
LOS Assert Time t_loss_on 100 µs 6
LOS Deassert Time t_loss_off 100 µs 7
Rate-Select Change Time t_ratesel 10 µs 8
Serial ID Clock Rate f_serial_clock 400 kHz

Notes:
1. Time from rising edge of TX Disable to when the optical output falls below 10% of nominal.
2. Time from falling edge of TX Disable to when the modulated optical output rises above 90% of nominal.
3. From power on or negation of TX Fault using TX Disable.
4. Time from fault to TX fault on.
5. Time TX Disable must be held high to reset TX_fault.
6. Time from LOS state to RX LOS assert.
7. Time from non-LOS state to RX LOS deassert.
8. Time from rising or falling edge of Rate Select input until receiver bandwidth is in conformance with appropriate specification.

Regulatory Compliance

The HSFP10-383X complies with international Electromagnetic Compatibility and international safety requirements and standards (see details in Table following).

Electrostatic Discharge
(ESD) to the Electrical Pins		 MIL-STD-883E
Method 3015.4		 Class 1(>2000 V)
Electromagnetic
Interference (EMI)		 FCC Part 15 Class B
EN55022 Class B (CISPR 22B)
VCCI Class B		 Compatible with standards
Laser Eye Safety FDA 21CFR 1040.10 and 1040.11
EN60950, EN (IEC) 60825-1,2		 Compatible with Class 1 laser product.
Product detail pictures:

2022 High quality Sfp-10g-Er40 - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel detail pictures

Related Product Guide:
No matter new customer or old customer, We believe in long term and trusted relationship for 2022 High quality Sfp-10g-Er40 - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel , The product will supply to all over the world, such as: Suriname, Uganda, Brasilia, They're durable modeling and promoting well all over the world. Under no circumstances disappearing key functions in a brief time, it's a must for yourself personally of fantastic quality. Guided by the principle of Prudence, Efficiency, Union and Innovation. the business make an awesome efforts to expand its international trade, raise its enterprise. rofit and improve its export scale. We have been confident that we will have a vibrant prospect and to be distributed all over the world in the years to come.
    • Adhering to the business principle of mutual benefits, we have a happy and successful transaction, we think we will be the best business partner.
    5 StarsBy Christopher Mabey from Rome - 2018.11.22 12:28
    Cooperate with you every time is very successful, very happy. Hope that we can have more cooperation!
    5 StarsBy Phoebe from Cologne - 2017.02.14 13:19
    Write your message here and send it to us

    Products categories

    Hit enter to search or ESC to close