English
Good Quality 10g Module - 10GBASE-LR SFP+1310nm 10km Hi-Optel HSFP10-2323 module – Hi-optel Featured Image
  • Good Quality 10g Module - 10GBASE-LR SFP+1310nm 10km Hi-Optel HSFP10-2323 module – Hi-optel

Good Quality 10g Module - 10GBASE-LR SFP+1310nm 10km Hi-Optel HSFP10-2323 module – Hi-optel

Short Description:


Download as PDF

Product Detail

Product Tags

Related Video

Feedback (2)

We are going to dedicate ourselves to providing our esteemed buyers together with the most enthusiastically thoughtful products and services for 25g Bidi , Sfp+ Transceiver Rj45 10g , Fiber Optic Sfp Module , Hope we are able to produce a far more superb long term with you by our efforts from the foreseeable future.
Good Quality 10g Module - 10GBASE-LR SFP+1310nm 10km Hi-Optel HSFP10-2323 module – Hi-optel Detail:

Descriptions

The transceiver consists of two sections: The high performance a 1310nm DFB Laser, Transmitter and high sensitivity PIN integrated with a TIA. Receiver.

A block diagram of the HSFP10-2323 SFP+ optical transceiver is shown below.

233

The module is hot pluggable into the 20-pin connector. The high-speed electrical interface is based on low voltage logic, with nominal 100 Ohms differential impedance and AC coupled in the module. The optical output can be disabled by LVTTL logic high-level input of TX_Disable. Loss of signal (RX_LOS) output is provided to indicate the loss of an input optical signal of receiver. The receiver RATE_SELECT pin is not used by the transceiver.

A 2-wire interface (SCL, SDA) is used for serial ID, digital diagnostics and other control /monitor functions.

● Absolute Maximum Ratings 

Parameter

Symbol

Min

Max

Unit
Storage Temperature

TST

-40

+85

 ℃
Supply Voltage

VCC3

0.0

+3.6

V
Relative Humidity

RH

5

95

%

● Recommend Operation Environment

Parameter

Symbol

Min

Typ

Max

Unit
Date Rate

10.3125

11.3

Gb/s
Supply Voltage

VCC

+3.14

3.3

+3.47

V
Supply Current

ICC

300

mA
Power Dissipation

PD

800

1000

mW
Operating Temperature

TOP

-40

25

+85

℃

● Optical Characteristics (Condition: Ta=TOP)

Parameter

Symbol

Min

Type

Max

Unit

Note
Transmitter
Date Rate

10.3125

11.3

Gb/s
Optical Wavelength

λ

1260

1355

nm
Average output power

Po

-6.5

0.5

dBm

1
Optical Extinction Ratio

ER

3.5

dB

1
Optical Modulation Amplitude

OMA

-5.2

dBm
Disabled Power Poff -30 dBm
Side Mode Suppression Ratio

SMSR

30

dB
Dispersion penalty

3.2

dB
Tx Jitter

Txj

Per 802.3ae requirements
Receiver
Date Rate

10.3125

11.3

Gb/s
Optical Wavelength

λ

1260

1355

nm
Receiver Sensitivity

R

-14.4

dBm

2
Receiver Sensitivity in OMA

R

-12.6
Stressed Receiver Sensitivity in OMA

R

-10.3

dBm

2
Maximum Input Power

PMAX

0.5

dBm
LOS De-Assert

LOSD

-15

dBm
LOS Assert

LOSA

-25

dBm
LOS Hysteresis

0.5

4

dB
Receiver Reflectance

-12

dB

Notes
Note 1. Measured at 10.3125b/s with PRBS 231 – 1 NRZ test pattern.
Note 2. Under the ER worst case, measured at 10.3125 Gb/s with PRBS 231 – 1 NRZ test pattern for BER< 1×10-12

● Electrical Characteristics (Condition: Ta=TOP)

Parameter

Symbol

Min

Typ

Max

Unit

Note
Transmitter
Differential input voltage swing

VI

150

1600

mVpp

1
Common mode voltage tolerance

15

-

-

mV
Transmit Disable Input

H

VIH

2.0

Vcc+0.3

V

L

VIL

0

0.8

V
Transmit Enable Output

H

VOH

2.4

Vcc+0.3

V

L

VOL

0

0.4

V

2
Data Dependent Input Jitter

DDJ

0.1

UI
Data Input Total Jitter

TJ

0.28

UI
Input Differential Impedance

Zin

80

100

120

Ω
Receiver
Differential output voltage swing

500

700

mVpp

3
LOS Output

H

VOH

2.4

Vcc+0.3

V

2

L

VOL

0

0.4

V
Rx Output Rise and Fall Time

Tr/Tf

30

ps

20% to 80%
Total Jitter

TJ

0.7

UI
Deterministic Jitter

DJ

0.42

UI
Output Differential Impedance

Zon

80

100

 120

Ω

Note 1. TD+/- are internally AC coupled with 100Ω differential termination inside the module.
Note 2. Tx Fault and Rx LOS are open collector outputs, which should be pulled up with 4.7k to 10kΩ resistors on the host board. Pull up voltage between 2.0V and Vcc+0.3V.
Note 3. RD+/- outputs are internally AC coupled, and should be terminated with 100Ω (differential) at the user SERDES.

Pin Assignment

Diagram of Host Board Connector Block Pin Numbers and Name

Pin Assignment

Product detail pictures:

Good Quality 10g Module - 10GBASE-LR SFP+1310nm 10km Hi-Optel HSFP10-2323 module – Hi-optel detail pictures

Related Product Guide:
To constantly improve the management system by virtue of the rule of "sincerely, good faith and quality are the base of enterprise development", we widely absorb the essence of related products internationally, and constantly develop new products to meet the demands of customers for Good Quality 10g Module - 10GBASE-LR SFP+1310nm 10km Hi-Optel HSFP10-2323 module – Hi-optel , The product will supply to all over the world, such as: Mexico, Luxembourg, luzern, Due to good quality and reasonable prices, our products have been exported to more than 10 countries and regions. We are looking forward to cooperating with all customers from at home and abroad. Moreover, customer satisfaction is our eternal pursuit.
    • It is really lucky to meet such a good supplier, this is our most satisfied cooperation, I think we will work again!
    5 Stars By Madge from Mumbai - 2018.10.31 10:02
    The company can think what our think, the urgency of urgency to act in the interests of our position, can be said this is a responsible company, we had a happy cooperation!
    5 Stars By Elma from Slovenia - 2018.10.31 10:02
    Write your message here and send it to us

    Products categories

    Hit enter to search or ESC to close