High reputation Bidi 10g Sfp - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel

Short Description:

Product Detail

Product Tags

Feedback (2)

"Sincerity, Innovation, Rigorousness, and Efficiency" will be the persistent conception of our company to the long-term to establish together with customers for mutual reciprocity and mutual gain for Sfp Sr Sx , 10ge Sr , Sfp Plus Module , Encouraged with the fast producing current market on the speedy foodstuff and beverage consumables all around the entire world , We're hunting forward to functioning with partners/clients to create good results together.

High reputation Bidi 10g Sfp - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel Detail:

Descriptions

Fiber type	Minimum modal bandwidth @ 850 nm (MHz●km)	Operatingra nge (meters)
62.5um MMF	160	2 to 26
62.5um MMF	200	2 to 33
50um MMF	400	2 to 66
	500	2 to 82
	2000	2 to 300

SFP+SR Operating Range for each Optical Fiber Type

The transceiver consists of two sections: The high performance 850nm VCSEL transmitter and high sensitivity PIN integrated with a TIA. Receiver.

A block diagram of the HSFP10-3831 SFP+ optical transceiver is shown below

● Absolute Maximum Ratings

Parameter	Symbol	Min	Max	Unit
Storage Temperature	T_ST	-40	+85	℃
Supply Voltage	V_CC3	0	+3.6	V
Relative Humidity	RH	5	85	%

● Recommend Operation Environment

Parameter	Symbol	Min	Typ	Max	Unit
Date Rate			10.3125		Gb/s
Supply Voltage	V_CC	+3.14	3.3	+3.47	V
Supply Current	I_CC		180	200	mA
Power Dissipation	PD			0.8	W
Operating Temperature	T_OP	-5	25	+75	℃

● Transmitter Operating Characteristic-Optical, Electrical

Parameter		Symbol	Min	Typ	Max	Unit	Ref.
Side Mode Suppression Ratio		SMSR	30	-		dBm
Average launch power of OFF transmitter		Poff		-	-30	dBm
Extinction Ratio		ER	3.5		-	dB	1
Transmitter Dispersion Penalty		TDP	-	-	3.9	dB
Operating Data Rate		S		10.3125		Gbps
Centre Wavelength		λC	840	850	860	nm
Spectrum Band Width (RMS)		σ			0.45	nm
Average Optical Power		Pavg	-7.3	-	-1	dBm
Optical Eye Mask		Compliant with IEEE 802.3ae
Input Differential Impedance		ZIN	90	100	110	Ω
TX Disable	Disable		2.0		Vcc+0.3	V
TX Disable	Enable		0		0.8	V
TX Fault	Fault		2.0		Vcc+0.3	V
TX Fault	Normal		0		0.8	V
Data Dependent Input Jitter		DDJ			0.08	UI
Data Input Total Jitter		TJ			0.25	UI

● Receiver Operating Characteristic-Optical, Electrical

Parameter		Symbol	Min	Typ	Max	Unit	Ref.
Center Wavelength		λr		850		nm
Average receiver power		PIN			-11.1	dBm	2
Receiver Overload		PMAX	-1.0			dBm	2
Los Assert		LosA	-30		-	dBm
Los Dessert		LosD			-12	dBm
Los Hysteresis		LosH	0.5	2.5	5	dB
Receiver Reflectance					-12	dB	1
Output Differential Impedance		PIN	90	100	110	Ω
LOS	High		2.0		Vcc+0.3	V
LOS	Low		0		0.8	V
Rx Output Rise and Fall Time		Tr/Tf	30			ps	20% to 80%
Total Output Jitter		TJ			0.7	UI
Data Dependent Output Jitter		DJ			0.42	UI

Notes:
Note 1. Measured at 10.3125b/s with PRBS 2³¹ – 1 NRZ test pattern.
Note 2. Under the ER worst case, measured at 10.3125 Gb/s with PRBS 2³¹ – 1 NRZ test pattern for BER

● Control and Status I/O Timing Characteristics

Parameter	Symbol	Min	Max	Unit	Ref.
TX Disable Assert Time	t_off		10	µs	1
TX Disable Negate Time	t_on		1	ms	2
Time to initialize including reset of TX_Fault	t_init		300	ms	3
TX Fault Assert Time	t_fault		100	µs	4
TX Disable to reset	t_reset	10		µs	5
LOS Assert Time	t_loss_on		100	µs	6
LOS Deassert Time	t_loss_off		100	µs	7
Rate-Select Change Time	t_ratesel		10	µs	8
Serial ID Clock Rate	f_serial_clock		400	kHz

Notes:
1. Time from rising edge of TX Disable to when the optical output falls below 10% of nominal.
2. Time from falling edge of TX Disable to when the modulated optical output rises above 90% of nominal.
3. From power on or negation of TX Fault using TX Disable.
4. Time from fault to TX fault on.
5. Time TX Disable must be held high to reset TX_fault.
6. Time from LOS state to RX LOS assert.
7. Time from non-LOS state to RX LOS deassert.
8. Time from rising or falling edge of Rate Select input until receiver bandwidth is in conformance with appropriate specification.

Regulatory Compliance

The HSFP10-383X complies with international Electromagnetic Compatibility and international safety requirements and standards (see details in Table following).

Electrostatic Discharge (ESD) to the Electrical Pins	MIL-STD-883E Method 3015.4	Class 1(>2000 V)
Electromagnetic Interference (EMI)	FCC Part 15 Class B EN55022 Class B (CISPR 22B) VCCI Class B	Compatible with standards
Laser Eye Safety	FDA 21CFR 1040.10 and 1040.11 EN60950, EN (IEC) 60825-1,2	Compatible with Class 1 laser product.