Wholesale Price 10g Sfp+ Bidi 80km - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel

Short Description:

Product Detail

Product Tags

Feedback (2)

We're commitment to offer you the aggressive cost ,superb products and solutions top quality, too as fast delivery for Gpon Olt Sfp Module , Gpon Ont Sfp Module , Cfp Optical Module , In case you are intrigued in any of our products or want to focus on a personalized get, please sense totally free to contact us. We're wanting ahead to forming successful enterprise relationships with new shoppers across the world during the in close proximity to long term.

Wholesale Price 10g Sfp+ Bidi 80km - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel Detail:

Descriptions

Fiber type	Minimum modal bandwidth @ 850 nm (MHz●km)	Operatingra nge (meters)
62.5um MMF	160	2 to 26
62.5um MMF	200	2 to 33
50um MMF	400	2 to 66
	500	2 to 82
	2000	2 to 300

SFP+SR Operating Range for each Optical Fiber Type

The transceiver consists of two sections: The high performance 850nm VCSEL transmitter and high sensitivity PIN integrated with a TIA. Receiver.

A block diagram of the HSFP10-3831 SFP+ optical transceiver is shown below

● Absolute Maximum Ratings

Parameter	Symbol	Min	Max	Unit
Storage Temperature	T_ST	-40	+85	℃
Supply Voltage	V_CC3	0	+3.6	V
Relative Humidity	RH	5	85	%

● Recommend Operation Environment

Parameter	Symbol	Min	Typ	Max	Unit
Date Rate			10.3125		Gb/s
Supply Voltage	V_CC	+3.14	3.3	+3.47	V
Supply Current	I_CC		180	200	mA
Power Dissipation	PD			0.8	W
Operating Temperature	T_OP	-5	25	+75	℃

● Transmitter Operating Characteristic-Optical, Electrical

Parameter		Symbol	Min	Typ	Max	Unit	Ref.
Side Mode Suppression Ratio		SMSR	30	-		dBm
Average launch power of OFF transmitter		Poff		-	-30	dBm
Extinction Ratio		ER	3.5		-	dB	1
Transmitter Dispersion Penalty		TDP	-	-	3.9	dB
Operating Data Rate		S		10.3125		Gbps
Centre Wavelength		λC	840	850	860	nm
Spectrum Band Width (RMS)		σ			0.45	nm
Average Optical Power		Pavg	-7.3	-	-1	dBm
Optical Eye Mask		Compliant with IEEE 802.3ae
Input Differential Impedance		ZIN	90	100	110	Ω
TX Disable	Disable		2.0		Vcc+0.3	V
TX Disable	Enable		0		0.8	V
TX Fault	Fault		2.0		Vcc+0.3	V
TX Fault	Normal		0		0.8	V
Data Dependent Input Jitter		DDJ			0.08	UI
Data Input Total Jitter		TJ			0.25	UI

● Receiver Operating Characteristic-Optical, Electrical

Parameter		Symbol	Min	Typ	Max	Unit	Ref.
Center Wavelength		λr		850		nm
Average receiver power		PIN			-11.1	dBm	2
Receiver Overload		PMAX	-1.0			dBm	2
Los Assert		LosA	-30		-	dBm
Los Dessert		LosD			-12	dBm
Los Hysteresis		LosH	0.5	2.5	5	dB
Receiver Reflectance					-12	dB	1
Output Differential Impedance		PIN	90	100	110	Ω
LOS	High		2.0		Vcc+0.3	V
LOS	Low		0		0.8	V
Rx Output Rise and Fall Time		Tr/Tf	30			ps	20% to 80%
Total Output Jitter		TJ			0.7	UI
Data Dependent Output Jitter		DJ			0.42	UI

Notes:
Note 1. Measured at 10.3125b/s with PRBS 2³¹ – 1 NRZ test pattern.
Note 2. Under the ER worst case, measured at 10.3125 Gb/s with PRBS 2³¹ – 1 NRZ test pattern for BER

● Control and Status I/O Timing Characteristics

Parameter	Symbol	Min	Max	Unit	Ref.
TX Disable Assert Time	t_off		10	µs	1
TX Disable Negate Time	t_on		1	ms	2
Time to initialize including reset of TX_Fault	t_init		300	ms	3
TX Fault Assert Time	t_fault		100	µs	4
TX Disable to reset	t_reset	10		µs	5
LOS Assert Time	t_loss_on		100	µs	6
LOS Deassert Time	t_loss_off		100	µs	7
Rate-Select Change Time	t_ratesel		10	µs	8
Serial ID Clock Rate	f_serial_clock		400	kHz

Notes:
1. Time from rising edge of TX Disable to when the optical output falls below 10% of nominal.
2. Time from falling edge of TX Disable to when the modulated optical output rises above 90% of nominal.
3. From power on or negation of TX Fault using TX Disable.
4. Time from fault to TX fault on.
5. Time TX Disable must be held high to reset TX_fault.
6. Time from LOS state to RX LOS assert.
7. Time from non-LOS state to RX LOS deassert.
8. Time from rising or falling edge of Rate Select input until receiver bandwidth is in conformance with appropriate specification.

Regulatory Compliance

The HSFP10-383X complies with international Electromagnetic Compatibility and international safety requirements and standards (see details in Table following).

Electrostatic Discharge (ESD) to the Electrical Pins	MIL-STD-883E Method 3015.4	Class 1(>2000 V)
Electromagnetic Interference (EMI)	FCC Part 15 Class B EN55022 Class B (CISPR 22B) VCCI Class B	Compatible with standards
Laser Eye Safety	FDA 21CFR 1040.10 and 1040.11 EN60950, EN (IEC) 60825-1,2	Compatible with Class 1 laser product.

Product detail pictures:

Related Product Guide:

We have now a skilled, performance group to offer excellent support for our consumer. We usually follow the tenet of customer-oriented, details-focused for Wholesale Price 10g Sfp+ Bidi 80km - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel , The product will supply to all over the world, such as: Germany, Egypt, Auckland, With the enterprising spirit of" high efficiency, convenience, practicality and innovation", and in line with such serving guidance of "good quality but better price, " and "global credit", we've been striving to cooperate with the automobile parts companies all over the world to make a win-win partnership.

10g Base Sx

10g Module

10g Sfp+ Rj45

10gb Sfp Sr

Sfp+ Transceiver Rj45 10g

Sfp-10g-Er40

Wide range, good quality, reasonable prices and good service, advanced equipment, excellent talents and continuously strengthened technology forces，a nice business partner.